- 您现在的位置：买卖IC网 > Sheet目录840 > B32572A3105K (EPCOS Inc)FILM CAP 1.0UF 10% 250V
B32572, B32573
Ignition (stacked) SilverCap TM
1.3
General notes on soldering
Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate-
gory temperature T max . Long exposure to temperatures above this type-related temperature limit
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings
The overheating associated with some of these factors can usually be reduced by suitable coun-
termeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.
EPCOS recommends the following conditions:
Pre-heating with a maximum temperature of 110 ° C
Temperature inside the capacitor should not exceed the following limits:
MKP/MFP 110 ° C
MKT 160 ° C
When SMD components are used together with leaded ones, the leaded film capacitors should
not pass into the SMD adhesive curing oven. The leaded components should be assembled af-
ter the SMD curing step.
Leaded film capacitors are not suitable for reflow soldering.
Uncoated capacitors
For uncoated MKT capacitors with lead spacings ≤ 10 mm (B32560/B32561) the following mea-
sures are recommended:
pre-heating to not more than 110 ° C in the preheater phase
rapid cooling after soldering
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 19
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
B32594C6684J008
CAP FILM 0.68UF 400VDC RADIAL
B32614A1223J008
CAP FILM 0.022UF 1.6KVDC RADIAL
B32621A3682J
CAP FILM 6800PF 250VDC RADIAL
B32632A7472K
CAP FILM 4700PF 1.25KVDC RADIAL
B32652A6154J
CAP FILM 0.15UF 630VDC RADIAL
B32656S7224K500
CAP FILM 0.22UF 1.25KVDC SCREW
B32669B6105K
FILM CAP 1.0000UF 10% 400VAC
B32671L1222J000
CAP FILM 2200PF 1.6KVDC RADIAL
相关代理商/技术参数
B32572A3105K000
功能描述:薄膜电容器 1.0UF 10% 250V FILM CAP MKT SILVER RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32572A3105K289
功能描述:FILM CAP MKT SILVER 1.0F 10% 250 制造商:epcos (tdk) 系列:* 零件状态:有效 标准包装:2,560
B32572A3155K
功能描述:薄膜电容器 Film Cap 1,5UF 10% 250V MKT SILVER RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32572A3155K000
功能描述:薄膜电容器 1.5UF 10% 250V FILM CAP MKT SILVER RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32572A3225J000
功能描述:FILM CAP MKT SILVER 2.2F 5% 250V 制造商:epcos (tdk) 系列:* 零件状态:有效 标准包装:600
B32572A3225K
功能描述:薄膜电容器 Film Cap 2,2UF 10% 250V MKT SILVER RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32572A3225K000
功能描述:薄膜电容器 2.2UF 10% 250V FILM CAP MKT SILVER RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm
B32572A3474J
功能描述:薄膜电容器 Film Cap 0,47UF 5% 250V MKT SILVER RoHS:否 制造商:Cornell Dubilier 产品类型: 电介质:Polyester 电容:0.047 uF 容差:10 % 电压额定值:100 V 系列:225P 工作温度范围:- 55 C to + 85 C 端接类型:Radial 引线间隔:9.5 mm